- Current Research in Dental Sciences
- Vol: 27 Issue: 1
- BİLGİSAYAR DESTEKLİ TASARIM-BİLGİSAYAR DESTEKLİ ÜRETİM VE PRESLEME SİSTEMLERİYLE ÜRETİLEN PORSELEN L...
BİLGİSAYAR DESTEKLİ TASARIM-BİLGİSAYAR DESTEKLİ ÜRETİM VE PRESLEME SİSTEMLERİYLE ÜRETİLEN PORSELEN LAMİNAT VENERLERİN KENAR VE İNTERNAL UYUMLARININ KARŞILAŞTIRILMASI: İN-VİTRO ÇALIŞMA
Authors : Ş. Mert Yüce, Ayşe Gözde Türk
Pages : 19-26
Doi:10.17567/ataunidfd.307095
View : 6 | Download : 2
Publication Date : 2017-04-16
Article Type : Research
Abstract :Amaç: Çalışmanın amacı, Bilgisayar destekli tasarım-Bilgisayar destekli üretim ve Isı ile Presleme yöntemleriyle üretilmiş porselen laminat venerlerin kenar ve iç yüzey uyumlarının karşılaştırılmasıdır. Gereç ve yöntem: Kenar ve iç yüzey uyumlarının fabrikasyon tekniğine göre farklılık gösterip göster- mediğini belirlemek amacıyla toplam 40 adet porselen laminat vener değerlendirildi. Venerler, Bilgisayar des- tekli tasarım-Bilgisayar destekli üretim ve Isı ile Presleme yöntemleriyle üretildi (n=20). Kenar ve iç yüzey uyumları replika tekniği kullanılarak değerlendirildi. Her bir venerin replikası akışkan kıvamlı elastomerik ölçü materyali kulanı- larak alındı ve replikalar, meziyo-distal ve insizo-gingival yönde kesildi. Her bir kesitin iç yüzey ve kenar uyumları ışık mikroskobunda x40 büyütme kullanılarak ölçüldü. İç yüzey uyumu için 9 nokta, kenar uyum içinse 3 nokta ölçüldü ve ortalamaları alındı. Levene ve independent samples t testi kullanılarak istatistiksel analiz yapıldı (p<0,05). Bulgular: Isı ile Presleme sistemi ile üretilen venerlerin kenar aralık değerleri (269±136,92 μm), Bilgisayar destekli tasarım-Bilgisayar destekli üretim ile üretilenlere (192±61,02 μm) göre daha yüksektir (p= 0,028). İki yöntemin iç yüzey aralık değerleri karşılaştırıldığında yine, Isı ile Presleme sistemi ile üretilen venerlerin iç yüzey aralık değerleri (190,43±63,33 μm), Bilgisayar destekli tasarım-Bilgisayar destekli üretim ile üretilenlere (105,61±24,39 μm) göre daha yüksektir (p=0,00). Sonuç: Bu çalışmanın kısıtlamaları dahilinde, Bilgisayar destekli tasarım-Bilgisayar destekli üretim yöntemi ile üre- tilen porselen laminat venerlerin kenar ve iç yüzey uyum- ları, Isı ile Presleme sistemi ile üretilenlere göre daha iyidir. Anahtar Kelimeler: Laminat vener, Bilgisayar destekli tasarım-Bilgisayar destekli üretim, Isı ile Presleme, Kenar uyum, İç yüzey uyumu, Replika yöntemi COMPARISON OF MARGINAL AND INTERNAL ADAPTATION OF COMPUTER AIDED DESIGN-COMPUTER AIDED MANUFACTURING AND HEAT-PRESSED CERAMIC LAMINATE VENEERS: AN IN-VITRO STUDY ABSTRACT Aim: The aim of this study was to evaluate the marginal and internal adaptations of porcelain laminate veneers produced with Computer aided design-Computer aided manufacturing and Heat-pressed techniques. Material and Methods: A total of 40 porcelain laminate veneers were evaluated whether the marginal and internal adaptations are changed due to fabrication technique. The veneers were fabricated with Computer aided design-Computer aided manufacturing and Heat-pressed techniques (n=20). The marginal and internal adaptations of veneers were measured by using a replica technique. Replicas of each veneer were obtained by using a light-body silicone impression material. The replicas were sectioned mesio-distally and gingivo-incisally. Then the marginal and internal gap adaptation of each cross section were measured by a stereomicros- cope at x40 magnification. Nine measurement locations for internal, 3 measurement locations for marginal adaptation were used to obtain the mean values. Levene and independent samples t-test was used to identify the statistical difference among the groups (p<0.05). Results: The mean marginal adaptation values of Heat-pressed and Computer aided design-Computer aided manufacturing veneers were 269±136.92 μm and 192± 61.02 μm respectively. There was a significant difference between the values (p=0.028). A significant difference was found between the internal adaptation values of Heat-pressed (190.43±63.33 μm) and Computer aided design-Computer aided manufacturing veneers (105.61± 24.39 μm) (p=0.00). Conclusion: Within the limitations of this in-vitro study, the Computer aided design-Computer aided manufac- turing veneers showed statistically better marginal and internal adaptation values than the Heat-pressed veneers. Keywords: Laminate veneer, Computer aided design-Computer aided manufacturing, Heat-pressed, Marginal adaptation, Internal adaptation, Replica techniqueKeywords : Laminat vener, Bilgisayar destekli tasarım-Bilgisayar destekli üretim, Isı ile Presleme, Kenar uyum, İç yüzey uyumu